Polycom® RMX® 4000 Hardware GuideVersion 6.0 | August 2010 | DOC2559A
Chapter 1- Hardware Description1-4MPMx Resource CapacitiesTwo MPMx card assemblies are available: MPMx - S (Single) and MPMx - D (Double) each offer d
Polycom RMX 4000 Hardware Guide1-5MPM+ Resource CapacitiesThree MPM+ card assemblies are available: MPM+ 80, MPM+ 40 and MPM+ 20 offering various reso
Chapter 1- Hardware Description1-6In HD Video Switching conferences, an RMX with four MPM+ cards can support up to 160 participants at HD1080p resolut
Polycom RMX 4000 Hardware Guide1-7• The RMX switches between MPMx and MPM+ Card Configuration Modes when MPM+/MPMx cards are removed or swapped while
Chapter 1- Hardware Description1-8Safety RequirementsThis section describes the requirements your site must meet for safe installation and operation o
Polycom RMX 4000 Hardware Guide1-9General Installation Precautions• Use a regulating uninterruptable power supply (UPS) to protect the RMX 4000 from p
Chapter 1- Hardware Description1-10• Always keep the rack’s trays and card’s slots closed when not servicing, to maintain proper cooling.Installing th
Polycom RMX 4000 Hardware Guide1-11Make sure that boxes contain all the required parts.4 Remove the boxes and top Stratocell®.5 Holding the handle on
Chapter 1- Hardware Description1-12Installing the RMX in a Rack or as a StandaloneEither place the RMX 4000 on a hard, flat surface such as a desktop
Polycom RMX 4000 Hardware Guide1-13Placing the RMX 4000 in a 19” Rack1 When the RMX is to be rack mounted chassis runners must be installed on the rac
Trademark InformationPolycom®, the Polycom “Triangles” logo, and the names and marks associated with Polycom’s products are trademarks and/or service
Chapter 1- Hardware Description1-143 Fasten the RMX to the rack with 8 screws into the holes provided on the RMX’s front as shown in Figure 1-3.Figure
Polycom RMX 4000 Hardware Guide1-15Placing the RMX 4000 in a 23” Rack1 Mounting the RMX 4000 on a 23” rack requires that first the handles and then th
Chapter 1- Hardware Description1-16The airflow of the RMX 4000 is from right to left. Be sure that the areas on the left and right side of the system
Polycom RMX 4000 Hardware Guide1-173 Place the RMX in a rack and tighten the 8 screws securing the RMX to the rack.Connecting the RMX 4000 to Power So
Chapter 1- Hardware Description1-18• Listed fastening hardware must be compatible with the materials being joined and must be preclude loosening, dete
Polycom RMX 4000 Hardware Guide1-19Connecting the RMX 4000 to -48DC SELV Power1 On the DC Power Rail Modules (PRM’s), set the two circuit breakers to
Chapter 1- Hardware Description1-205 Connect the green or green-yellow wire to the system single-point M6x15 “Ground” bolt.If the unit is rack mounted
Polycom RMX 4000 Hardware Guide1-21Connecting Cables on the RMX 4000To connect the cables (AC and DC systems):• RTM-IP 4000:— Connect the Management N
Chapter 1- Hardware Description1-22For more information about specific card connections, see:• "RTM-IP 4000” on page 1-37• "RTM ISDN” on pag
Polycom RMX 4000 Hardware Guide1-23RMX 4000 ComponentsOn the RMX 4000 components are located on both the front and rear of the MCU as listed in Table
CE MARK R&RTTE DirectiveČesky [Czech]: Polycom (UK) Ltd tímto prohlašuje, že tento RMX 4000 je ve shodě se základními požadavky a dalšími příslušn
Chapter 1- Hardware Description1-24Figure 1-8 shows the front panel of an RMX 4000 DC system.Figure 1-8 RMX 4000 DC Front ViewTable 1-5 Polycom RMX
Polycom RMX 4000 Hardware Guide1-25AC/DC Power Supply ModulesThe AC Power Supply drawers are located below the MPM+/MPMx Cards and are connected to th
Chapter 1- Hardware Description1-26Multi Processor Module x (MPMx) CardThe MPMx cards, perform the various RTP, audio and video processing functions o
Polycom RMX 4000 Hardware Guide1-27RMX 4000 Rear PanelThe RMX 4000 rear panel contains the RTM-IP 4000 card and either (or both) RTM ISDN/RTM LAN card
Chapter 1- Hardware Description1-28Figure 1-10 RMX 4000 DC Rear ViewRTM-IP 4000A single RTM-IP 4000 card provides system management based on the ATCA
Polycom RMX 4000 Hardware Guide1-29Figure 1-11 RMX 4000 RTM-IP 4000 Rear Panel LayoutThe following items appear on the RMX 4000 rear panel:LAN 6- 10/1
Chapter 1- Hardware Description1-30RTM ISDNThe RTM ISDN card connects directly to an MPM+/MPMx. The RTM ISDN card routes data between the MPM+/MPMx ca
Polycom RMX 4000 Hardware Guide1-31.ISDN/PSTN Clock SourceEach RTM ISDN card has its own primary and secondary clock source. The first span to synchro
Chapter 1- Hardware Description1-32AC Power Entry Module (PEM)An AC PEM includes a power inlet, EMI filter and backplane connectors. Power input to th
Polycom RMX 4000 Hardware Guide1-337 Logo Panel Not Available (NA)8 CTNL 4000 unit (CPU 1)Mandatory9-11 AC Power Supply An RMX with AC power has 3 pow
Polski [Polish]: Niniejszym Polycom (UK) Ltd oświadcza, że RMX 4000 jest zgodne z zasadniczymi wymaganiami oraz innymi stosownymi postanowieniami Dyre
Chapter 1- Hardware Description1-34RMX 4000 LEDsThe RMX includes LEDs located on the front panel and rear panel. In the front panel, the LEDs reflect
Polycom RMX 4000 Hardware Guide1-35Fabric Switch Module (FSM 4000)ERR Red ON - Major error on card.Flashes - During card startup.RDY Green ON - The ca
Chapter 1- Hardware Description1-36CNTL 4000 Unit ERR Red ON - Major system error. In case of an active alarm this light is ON, and the RDY green is O
Polycom RMX 4000 Hardware Guide1-37RMX 4000 Rear Panel LEDsRTM-IP 4000The following LEDs appear on the RTM-IP 4000 card:Table 1-9 RMX 4000 RTM-IP 400
Chapter 1- Hardware Description1-38RTM LANThe following LEDs appear on the RTM LAN:ShMG (Shelf Manager) LEDsERR Red ON - Major error on RTM-IP 4000 ca
Polycom RMX 4000 Hardware Guide1-39RTM ISDNThe following LEDs appear on the RTM ISDN:Table 1-11 RMX 4000 RTM ISDN LEDs Function NameLED NameLED Color
Chapter 1- Hardware Description1-40
2Component ReplacementThe RMX 4000 is designed with ease of maintenance in mind. Most components are swappable and are accessible directly via the fro
Chapter 2- Component Replacement2-2• Fabric Switch Module (FSM 4000), see “Replacing the Fabric Switch Module (FSM 4000)” on page 2-18.Before replacin
Polycom RMX 4000 Hardware Guide2-3Using the Modified PMC Compatible Ejector LeverOn the RMX 4000 most components are fitted with identical ejector lev
Polycom RMX 4000 Hardware GuideiTable of ContentsHardware Description . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1Main Features ...
Chapter 2- Component Replacement2-4Replacing the CNTL 4000 ModuleThe CPU module is the management system of the RMX 4000. Use the following procedure
Polycom RMX 4000 Hardware Guide2-5Replacing an AC Power Supply ModuleTwo units supply power to the RMX 4000 (3rd optional - AC only), each unit with i
Chapter 2- Component Replacement2-63 Carefully slide the Power Supply unit out from the front slot.4 Slide in the replacement Power Supply unit.5 Pus
Polycom RMX 4000 Hardware Guide2-74 Carefully slide the PEM unit out from the rear slot.5 Slide in the replacement PEM unit.6 Push the PEM unit firml
Chapter 2- Component Replacement2-84 Using a star screw driver, disconnect the two wires connected to the Terminal block (-48 VDC & RTN) of the fa
Polycom RMX 4000 Hardware Guide2-9Replacing the Fan DrawerEight fans are mounted in the Fan drawer, where the airflow is from right to left. Should on
Chapter 2- Component Replacement2-10Inserting an Air Filter (Optional) in the Fan DrawerIn the fan drawer, an Air Filter can be added as an option. Yo
Polycom RMX 4000 Hardware Guide2-115 Open the filter tray, by unscrewing two screws on the tray.6 Insert the air filter into the filter tray.7 Close
Chapter 2- Component Replacement2-121 If applicable, loosen the captive screws and remove the slot cover.2 Power down the card by partially opening th
Polycom RMX 4000 Hardware Guide2-135 Carefully slide the MPM+/MPMx card out through the front panel.Installing the Replacement MPM+/MPMx Card1 On the
Table of ContentsiiISDN/PSTN Clock Source ... 1-31RTM LAN ...
Chapter 2- Component Replacement2-14Installing an MPM+/MPMx Card on the RMX 40001 If applicable, loosen the captive screws and remove the slot cover.2
Polycom RMX 4000 Hardware Guide2-156 On the card to be installed, move the ejector levers to their fully open position.7 Slide in the replacement RTM
Chapter 2- Component Replacement2-16Replacing the RTM-IP 4000The RTM-IP 4000 card on the rear of the RMX 4000 provides connectivity to all the MCU mod
Polycom RMX 4000 Hardware Guide2-1710 Tighten the captive screws on the rear panel of the RMX 4000 that secure the RTM-IP 4000 card.11 Reconnect the c
Chapter 2- Component Replacement2-189 Ensure that the metal ejector levers are fully retracted into their housings.10 Tighten the captive screws on th
Polycom RMX 4000 Hardware Guide2-198 Ensure that the metal ejector levers are fully retracted into their housings.9 Tighten the captive screws on the
1Hardware DescriptionThis Hardware Guide provides information on the RMX 4000 and its components. This system utilizes a modular “universal slot” plat
Chapter 1- Hardware Description1-2RMX 4000 SpecificationsTable 1-1 Polycom RMX 4000 Specifications PhysicalHeight 6U (26.56 cm.)Width 19” (48.26 cm.)
Polycom RMX 4000 Hardware Guide1-3RMX 4000 System CapacitiesThe following table summarizes the different system capacities.Operating temperature 10°–
Comments to this Manuals